معلومات البحث الكاملة في مستودع بيانات الجامعة

عنوان البحث(Papers / Research Title)


EFFECT OF ANNEALING TEMPERATURE ON PHYSICAL PROPERTIES Of INDIUM DOPED CADMIUM OXIDE THIN FILMS


الناشر \ المحرر \ الكاتب (Author / Editor / Publisher)

 
ايناس محمد سلمان الربيعي

Citation Information


ايناس,محمد,سلمان,الربيعي ,EFFECT OF ANNEALING TEMPERATURE ON PHYSICAL PROPERTIES Of INDIUM DOPED CADMIUM OXIDE THIN FILMS , Time 12/12/2016 06:09:20 : كلية العلوم

وصف الابستركت (Abstract)


Nanostructured indium doped CdO thin films were prepared by spray pyrolysis on glass substrate and annealed at 200-400 ?C for 1 hour

الوصف الكامل (Full Abstract)

ISSN 2321-807X
3478 | P a g e F e b r u a r y 2 8 , 2 0 1 5
EFFECT OF ANNEALING TEMPERATURE ON PHYSICAL PROPERTIES Of INDIUM DOPED CADMIUM OXIDE THIN FILMS Jinan A. Abd1, Enas M. Al-Robayi2, Zainab J. Shanan3, Nadir F. Habubi4 1,2 laser Physics Department, College of Science for Women, University of Babylon, Iraq. E-mail: jinanali7077@yahoo.com E-mail: dr.enas17@yahoo.de 3 Physics Department, College of Science for Women, Baghdad University, Iraq. E-mail: zainabjassim73@yahoo.com 4 Physics Department, College of Education, Al-Mustansiriyah University, Iraq. E-mail: nadirfadhil@yahoo.com ABSTRACT Nanostructured indium doped CdO thin films were prepared by spray pyrolysis on glass substrate and annealed at 200-400 ?C for 1 hour. The structural, optical, and electrical properties of prepared films were studied using different techniques such as optical transmission, photoluminescence, X-ray diffraction, and Hall measurement. X-ray analysis shows that the In doped CdO films are preferentially orientated along (111) crystallographic directions. Increasing of annealing temperature increases the films packing density and reorient the crystallites along (1 1 1) plane. The optical transmissions of all annealed films decreased with increasing annealing temperature. An increasing in the absorbance and photoluminescence spectra with increasing annealing temperature was denoted in all films. The band gap value of CdO:4%In equals to 2.5 eV and it decreases with annealing temperature and reaches of 2.45 eV for 400°C. The resistivity of annealed films decreased as annealing temperature increased. While high conductivity achieved in the present study is found to be 11.37 ×102 (?.cm)-1 for annealing at 400°C. Keywords: Thin film; Annealing; Structural properties; CdO; CdO:In; Optical properties; Hall measurements.
Council for Innovative Research
Peer Review Research Publishing System
Journal: Journal of Advances in Chemistry Vol. 11, No. 4 editorjaconline@gmail.com www.cirjac.com
ISSN 2321-807X
3479 | P a g e F e b r u a r y 2 8 , 2 0 1 5
1. INTRODUCTION
Metallic oxides are a materials class showing one of the greatest range of properties –superconducting, ferroelectric, ferromagnetic [1], multiferroic, magneto-resistive, dielectric, or conducting. Of particular interest are the so-called transparent conducting oxides (TCOs). The TCOs are heavily used for flat panel displays, photovoltaic cells, low emissivity windows, electrochromic devices, sensors and transparent electronics [2,3]. Among the metal oxide semiconductors CdO is an n-type semiconductor and has a rock-salt structure, in which each Cd or O ion is surrounded by 6 neighbors. In contrast to the other TCOs, it has a minimum optical band gap of about 2.2-2.5 eV [4]. CdO has high electrical conductivity and optical transmittance in the visible region of the solar spectrum. Due to these properties of CdO, it is one of the promising TCO from II to VI group of semiconductors. CdO films have been prepared so far by many different methods which are chemical bath deposition (CBD) [5], pulsed laser deposition [6], sol-gel [7], magnetron sputtering [8], metal-organic chemical vapor deposition [9], and successive ionic layer adsorption and reaction (SILAR) methods [10]. When these various oxides are doped with donors, the free electrons lie in the lowest conduction band. The next available empty state after this is not the conduction band minimum itself, but higher unoccupied conduction states. This increases the energy of the lowest optical transition, the optical gap. This is the Moss-Burstein shift, and varies inversely with the effective mass [11]. Indium has been used as a suitable dopant for transparent conducting films to increase the concentration of conduction electrons and improve the electrical conductivity. The dopant In ions in CdO film can either enter into the crystalline structure of CdO existing mainly in substitutional state or adsorbed in grain boundary regions. Since In ions substituting Cd ions in Cd lattice can liberate more conducting electrons in the conduction band, the increase of In concentration to certain level can significantly enhance the concentration of electrons and hence the carrier concentration [12]. In this work spray pyrolysis technique has been used to prepare CdO:4%In films because it is simple, cost effective and suitable for large area thin films preparation with homogenous doping level [13] which are attractive for photoelectronic devices . Also we reported the effect of annealing temperature on structural, optical, and electrical properties of In doped CdO thin film. 2. EXPERIMENTAL Spray pyrolysis deposition technique was used to prepare CdO:4%In thin films on glass substrates . An 0.1M solution of cadmium acetate Cd(CH3COO)2.2H2O diluted with methanol and water in ratio 1:1 was used to prepare CdO solution. CdO:In thin films were prepared by doping CdO solution in ratio(4%) of InCl3 and water mixture with 0.1 M . The deposition parameters were: The distance between the nozzle and the substrate was maintained at 31 cm, the substrate temperature of 350°C was controlled within ±10°C by using an iron-constant thermocouple, nitrogen gas with a pressure of 4 bar, spray time (7 s) and the spray interval (70 s) .The thicknesses of the films were measured to be 234 nm using Mlichlson Interferometer. The chosen films were annealed to (200, 300, and 400 °C) for 1 hour. The annealed films were characterized for their physical properties using the appropriate techniques. The crystalline structure of the films was confirmed by X-ray diffraction (XRD) with Cu K? radiation (Rigaku Model, ? = 1.5406A°). The accelerating voltage of 40 kV, emission current of 30 mA and the scanning speed of 2° per min were used. The transmittance and absorbance spectra for all films were recorded by (UV/VIS, Cecil ,Cez200,7000Series, Metertec). The photoluminescence spectrum of all films was recorded by Hitachi F-2500 FL Spectro-photometer. 3. RESULTS AND DISCUSSION
3.1 Structural Properties Figure 1 shows the X-ray diffraction (XRD) patterns of the prepared CdO and CdO: 4%In films . For the as-deposited films, the XRD peak associated with the (111), (200), (220) planes of the cubic structure (JCPDS Card No:05-0640) [14] are observed. The (111) plane of the CdO crystal grew more predominantly than the other planes, and its intensity increased with doping and annealing. The shift in the preferential orientation of the XRD peaks due to the incorporation of some of the cations and various deposition conditions were also reported by earlier workers [15,16]. When annealing increases from 200°C to 400°C, the crystallite size also increases from 42.8 nm to 74.3 nm. The intensity of the diffraction peak was also found to increase with increasing annealing temperature and get sharper with decreasing full width half maximum (FWHM). This can be attributed to the improvement in crystallinity of CdO:4%In thin films. The structural parameters of annealed and unannealed CdO:4%In thin films are given in Table 1. For all films, the grain size (D) was calculated from the full width at half maximum (FWHM) (?) of the preferential orientation diffraction peak by using the Scherrer equation [17]: D=??.????.???????? (1) Where k denotes the Scherrer constant (the shape factor of the average crystallite and can be considered k = 0.90 ¸ ?= 1.5406 ? is the wavelength of the incident Cu K? radiation.
ISSN 2321-807X
3480 | P a g e F e b r u a r y 2 8 , 2 0 1 5
Fig. 1: The X-ray diffraction (XRD) patterns of CdO and CdO:4%In films annealed at 200, 300 and 400 °C According to Table 1, the films have better crystallinity levels after annealing. Similar results have been reported for annealed CdO films prepared by SILAR method [18]. Additionally, to have more information on the amount of defects in the films, the dislocation density (d) was evaluated from the formula [19]: ?=1??² (2) Where D is the grain size. This quantity, ?, is defined as the number of dislocations intersecting a unit area of a random section. It is seen from Table 1 that the ? value of all films is decreased with increasing annealing temperature. This means, annealing decreases the defects in the CdO:4%In films and improves crystallite quality. This can be attributed to the improvement in crystallinity due to the regular arrangements of atoms in the crystal lattice [18]. Moreover the texture coefficient TC (hkl) is introduced to characterize the preferential crystallite orientation along the (hkl) direction defined as [20]: TC( hkl ) = I(hkl)/I?(hkl)N?¹ I(hkl)/I?(hklN) (3) Where I (hkl), I? (hkl) and N are the measured relative intensity of a diffraction peak, intensity of the standard powder diffraction peak and the number of diffraction peaks respectively. The TC values of the preferential crystallite orientation (111) of all the films were presented in Table 1. It can be observed that all the films had values larger than 1, which indicate the profusion of crystallite in a given (hkl) direction. The calculated lattice constant for the dominant peak of (1 1 1) of the films is tabulated in Table 1. However a shift in lattice constant towards its standard value a?= 4.695 ? [21] is observed when the films annealed from 200 to 400 °C. From Table 1, it is evident that the post annealing process improves the quality of the crystalline thin films and gives an indication that the crystallite size lie within the nanocrystal range.
ISSN 2321-807X
3481 | P a g e F e b r u a r y 2 8 , 2 0 1 5
Table 1: FWHM (?), texture coefficient (TC), the grain size (D) and the dislocation density ( ?) of the annealed CdO:4%In films a (?) ?× 10?4 (nm?2) D (nm) TC ?×10?³ (rad) Preferentil Orientation Annealing Temperature Material 4.683 10.74 30.5 1.49 4.7414 (111) - CdO:4%In 4.689 5.45 42.8 1,51 3.2392 (111) 200 CdO:4%In 4.692 3.61 52.6 1.54 2.6347 (111) 300 CdO:4%In 4.696 1.81 74.3 1.56 1.8654 (111) 400 CdO:4%In
3.2 Optical Properties Optical transmittance spectra of annealed films of different temperature in the range of 300–900 nm are presented in Figure 2, measured at room temperature in air. Optical transmittance spectra of CdO thin film in a previous work [22] showed an increasing with increasing In doping up to (4%wt.). As seen in this figure, the optical transmission of all films decreased with increasing annealing temperature. The unannealed film shows a transmittance of 78.9% (900 nm) while the annealing up to 400°C decreases the transmittance value to 66% (900 nm). On contrary of absorbance spectra of all films which exhibit an increasing in light absorption with increasing annealing temperature. This is possibly due to increase in crystalline nature and decrease in the number of defects in the localized state [23]. Hence these films can be used as optical filters and optical switches.
Fig. 2 : Optical transmittance spectra of CdO:4%In films annealed at 200, 300 and 400 °C Figure 3 shows the variation of the optical absorbance coefficient with wavelength. The absorption coefficient (?) is calculated using the equation [24]: ? = ln (1/T) / d (4) Where T is transmittance and d is film thickness. The sharp increase in absorbance at the wavelength ? ? 550 nm is due to the inception of inter band transitions at the fundamental edge.
ISSN 2321-807X
3482 | P a g e F e b r u a r y 2 8 , 2 0 1 5
Fig. 3 : The variation of the optical absorbance coefficient with wavelength of CdO:4%In films annealed at 200, 300 and 400 °C The optical band gap values obtained by extrapolating the linear portion of the plots of (?h?)² versus (h?) to ?= 0 [25]. These plots are given in Figure 4. From the figure it was determined that all films have a direct band transition. It is observed that the band gap energy decreases with increasing annealing temperature. The band gap of non annealed CdO:4%In film was found to be 2.5 eV. The band gap energy was found to be 2.48 eV, 2.47 eV and 2.45 eV for the films annealed at 200, 300 and 400 °C, respectively. Similar trend was also seen in films prepared by sol gel method [26]. This slightly decrease in optical band gap energy with increasing annealing temperature may be due to the increase in the carrier concentration and also may be due to sinter of the nanocrystalline and increasing in lattice parameter and grain size[27].
Fig. 4: The (?h?)2 versus photon energy (h?) for CdO:4%In films annealed at 200, 300 and 400 °C All the measured and calculated values of optical properties and constants of all prepared films at the fundamental edge were tabulated in Table 2. This table a show how is the annealing improves the optical properties of CdO:4%In film. Such as the refractive index and extinction coefficient which are increased as annealing temperature increased. This trend can be attributed to the increase of optical absorption in the UV-visible region when increasing annealing temperature [28].
ISSN 2321-807X
3483 | P a g e F e b r u a r y 2 8 , 2 0 1 5
Table 2 : All the measured and calculated values of optical properties and constants of the annealed films Eg eV ?×104 cm-1 K n R% A% T% Annealing Temp. °C Material ? = 550 nm 2.5 2.2191 0.097 1.966 17.9 22.5 59.5 - CdO:4%In 2.48 2.4706 0.108 2.02 18.8 25.1 56.1 200 CdO:4%In 2.47 3.2545 0.142 2.133 20.2 33 46.7 300 CdO:4%In 2.45 4.0356 0.176 2.156 20 41 38.9 400 CdO:4%In
(Figure 5) shows the PL spectra of the CdO:4%In films of annealed at 200, 300 and 400 °C. One part can be distinguished in this spectrum which is composed of a narrow peak located at higher energies corresponding to excitonic emission (550 nm). This main peak is located at about 2.25 eV and is due to an exciting bound to a donor level [29]. The intensity of unannealed film was increased as annealing temperature increased. This is may be due to improve the crystalline nature and decrease in the number of defects in the localized state.
Fig. 5: Photoluminescence spectra of CdO:4%In films annealed at 200, 300 and 400 °C 3.3 Electrical Properties Hall voltage measurement was made to determine some electrical properties for un-doped and In doped samples at room temperature in a constant magnetic field of 0.55T. Hall constant (R?), the conductivity (?), electrical resistivity (?), carrier concentration (Ne) and mobility (?) have been calculated from Hall voltage and the reported values are tabulated in Table 3. Hall measurement indicates that In-doped CdO are n-type material and electrons are the majority carrier of current which results in the presence of Cd ion interstitials or oxygen vacancies as donors. It has been said that to achieve highly conducting thin films, the carrier concentration need to be very high. From Table 3, it is clear, that carrier concentrations of all films increased with increasing annealing temperature. The higher carrier concentration can be attributed to the presence of both cadmium interstitials and oxygen vacancies [30]. The mobility of CdO:4%In thin films decreases from 79.4 to 75.3 cm2/(V.s) as temperature increases from 200 to 400°C. This decreasing may be due to the lattice scattering of charge carriers since the ionized impurity scattering is independent of temperature [31]. The variation of electrical conductivity (?) as a function of annealing temperature is shown in Figure 6. From the figure one can observe that the conductivity of the films was found to increase with increasing annealing temperature. On contrary of resistivity and Hall constant which they decreased as annealing temperature increases, show Table 3. These changes are resulted from the variation in Ne and carrier scattering [32].
ISSN 2321-807X
3484 | P a g e F e b r u a r y 2 8 , 2 0 1 5
Table 3: The Hall constant (R?) , the conductivity (?), electrical resistivity(?) ,carriers concentration(Ne) and mobility(?) of the annealed thin films. ?(cm²/V.s) Ne×1019(cm?³) ?×10?³(?.cm) ?×10²(?.cm)?¹ R?×10?²(cm³/C) Annealing Temp. °C Material 83.6 8.07 0.925 10.81 7.74 - CdO:4%In 79.4 8.64 0.910 10.98 7.23 200 CdO:4%In 77.1 9.13 0.887 11.27 6.84 300 CdO:4%In 75.3 9.44 0.879 11.37 6.62 400 CdO:4%In
Fig. 6: The variation of electrical resistivity (?) as a function of annealing temperature 4. CONCLUSION Nanostructured CdO:4%In thin films are prepared by means of simple and low cost spray pyrolysis method. Post-annealing process helps to improve the crystalline quality of the CdO:4%In thin films. XRD shows that the films have a cubic crystal structure. The average grain size of (1 1 1) orientation grains of the studied polycrystalline film annealed at 400°C was found to be around 74.3 nm and before annealed grains was found to be around 30.5 nm. The annealing improves the optical properties of CdO:4%In film. An increasing in the absorbance and photoluminescence spectra with increasing annealing temperature was denoted in all films .An optical transmittance spectrum shows the NIR transmittance. The unannealed film shows a transmittance of 78.9% (900 nm) while the annealing up to 400°C decreases the transmittance value to 66% (900 nm). Direct band gap of about 2.45 eV for the film annealed at 400 °C for 1 h. High conductivity achieved in the present study is found to be 11.37 ×102 (?.cm)-1 for annealing at 400°C. The carrier concentration of about 9.44 ×1019(cm?³) and resistivity of 0.879×10?³(?.cm) are achieved for the films annealed at 400 °C for 1 h which are comparable with the films prepared by using high cost physical and chemical deposition techniques. REFERENCES [1] Ahn ,C. H., Triscone ,J. M., and Mannhart ,J., 2003, Nature, 424, 1015. [2] Ginley, D. S. and Bright, C., 2000 (eds) MRS Bull , 25. [3] Hamberg ,I. and Gramquist, C. G.,1986, J App Phys , 60, 123. [4] Ortega, M., Santana, G, and Morales, A. A., 2000, Solid-State Electronics, 44, 10,1765–1769. [5] Gutiérrez, L.R, Cayente-Romero, J.J., Peza-Tapia, J.M., Barrera-Calva, E., Mart?nez-Flores, J.C., and Ortega-L?pez, M., Materials Letters, 2006, 60, 3866–3870. [6] Shagnov, I.I., Kryzhanovskii,B.P. and Dubkov,V.M. , 1981, Sov. J. Opt. Technol., 48, 280.
ISSN 2321-807X
3485 | P a g e F e b r u a r y 2 8 , 2 0 1 5
[7] Cruz, J.S., Delgado, G.T, and Perez, R.C., 2005, Thin Solid Films, 493, 83–87. [8] Subramanyam, T.K., Uthanna, S., and Naidu, B.S., 1998, Materials Letters, 35, 214–220. [9] Liu, X., Li, C., Han, S., Han, J., and Zhou, C., 2003, Applied Physics Letters, 82, 1950–1952. [10] Salunkhe, R.R. and Lokhande, C.D., 2008,Sensors and Actuators B, 129, 345–351. [11] Hamberg, I., and Gramquist, C. G., 1986, J App Phys , 60, 123. [12] Dakhel, A.A., 2009,Journal of Alloys and Compounds, 475, 51–54. [13] Kumaravel, R. , Ramamurthi, K. and Krishnakumar ,V., 2010, Journal of Physics and Chemistry of Solids, 71, 1545–1549. [14] JCPDS—International Centre for Diffraction Data, 1997, Card No. 05 - 0640. [15] Jin, S. ,Yang, Y., Medvedeva, J.E., Ireland, J.R., Metz, A.W., Ni,J. Kannewurf ,C.R., Freeman , A.J., and Marks ,T.J., 2004, J. Am. Chem. Soc., 126, 13787. [16] Koida ,T. and Kondo, M., 2007, J. Appl. Phys., 101, 0637131. [17] Rusu ,D.I., Rusu ,G.G. , Luca, D., 2011, Acta Physica Polonica A, 119 , 850-856. [18] . Gokul, P. M., and Sathyamoorthy, R., 2013,J. Mater. Sci. Technol., 29, 17-21. [19] Callister W.D.1997 "Materials Science and Engineering – An Introduction", New York, John Wiley and Sons. [20] Saleem, M. , Fang, L. , Ruan, H. B. Wu ,F., Huang ,Q. L., Xu ,C. L. , and Kong ,C. Y.,2012 International Journal of Physical Sciences , 7 , 2971-2979. [21] Khan ,M.K.R., Rahman ,M.A., Shahjahan , M., Rahman ,M.M., Hakim ,M.A., Saha , D.K. , and Khan ,J.U., Current. 2010, Appl. Phys., 10, 790. [22] Habubi ,N. F., Al-Anssari, R. A., and Abd ,J. A., 2013, Nano Science and Nano Technology, 7(5), 172-178. [23] Khudiar, A.I., Zulfequar ,M., Khan ,Z.H., 2012, Mater Sci Semicond Process, 15, 536. [24] Miao ,W., Li ,X., Zhang ,Q., Huang ,L., Zhang ,L. , and Yan ,X., 2006, Thin Sold Films, 500, 70. [25] Kose ,S., Atay ,F., Bilgin ,V. And Akyuz ,I., 2009 International Journal of Hydrogen Energy, 34, 5260 – 5266. [26] Aksoy ,S., Caglar ,Y., Ilican ,S., and Caglar,M. 2009,Int. J. Hydrogen Energy, 34, 5191-5195. [27] Abdul-Hussein K. E., Hayder M. A., and Ausama I. Kh., 2013, Journal of Materials Research and Technology, 2, 182–187. [28] Ziabari, A. A. and Ghodsi, F.E. 2011, Acta Physica Polonica A, 120, 536-540. [29] Dong, J. S., 2004, Journal of the Korean Physical Society, 45, 1575-1579. [30] Tanaka, K., Kunioka ,A., and Sakai ,Y., 1969 Jpn. J. Appl. Phys.,8 , 681-691. [31] Yan ,M., M. Lane, Kannewurf ,C.R., and Chang R.P.H. 2001 , Appl. Phys. Lett., 78, 2342-2344. [32] Zheng ,B.J. , Lian, J.L., Zhao, L., and Jiang ,Q., 2010, Appl. Surf. Sci., 256, 2910.

تحميل الملف المرفق Download Attached File

تحميل الملف من سيرفر شبكة جامعة بابل (Paper Link on Network Server) repository publications

البحث في الموقع

Authors, Titles, Abstracts

Full Text




خيارات العرض والخدمات


وصلات مرتبطة بهذا البحث